Sekonic's camera calibration

Spread the love

The Sekonic Digitalmaster L-758D meter offers the solution to variable ISO/EI ratings, and apparent sensitivity and contrast curves variations found in DSLRs. With a USB interface to link it up to a PC/Mac calibration program, the L-758D can remember three different cameras, two types of lighting (ambient or flash) and two measuring methods (incident or reflected) plus a range of ISO values for each of the cameras. There are twelve basic ‘profiles’ that can be stored, and within each profile a range from ISO 3 to ISO 8000.

The three cameras can include settings on a single camera such as Landscape+sRGB+High Contrast, or Portrait+AdobeRGB+Low Saturation+Low Contrast. More likely, they will be three different generations or even different makes of digital SLR, as many studios keep their last models when buying new ones. They can equally well be films used in a particular film camera, though you need a scanner or a densitometer for calibrating film.

You might think a meter costing over £300 and coming with a USB cable and a program to do the calibration would include the necessary calibration target. But it’s incapable of actually doing the calibration until you spend another £99.99 on a special A4 grey scale card. Since this report was written, a new more accurate target card has been introduced.

My sample test target arrived packed in a carton large enough to contain a camera. It is quite fragile, and obviously hand-made using special papers and perhaps a type of inkjet printing for the black patches. You could not just shove this in a camera bag and use it as a grey card. It should be kept in its envelope and stored away from light, like an archival print.

Basic functions

The Sekonic appeared to agree with power adjustments made to my Elinchrom flash units, which claim a 1/10th of a stop accuracy.

I found it to agree with my Minolta Flashmeter IV (which can be user calibrated with a small potentiometer in the back, but only for overall sensitivity). The L-758D should never need to go back to base as a default calibration can be programmed in to it, and this can cope with non-linear responses.

The L-758D will measure flash versus ambient, compare light source contrasts, or compare incident and digital much like any other modern digital meter. You can take up to nine spot or local measurements, pressing the M memory button after each one, then pressing the Average button for a calculated average exposure. Contrast (they recommend you turn each light off and only measure one at a time) is shown in EV values.

The reflected light metering via a semi-spot type viewfinder replaces any other type of reflected reading. Unlike the Gossen Spotmaster F you don’t get information shown in the finder, you just use the sighting to make the reading and must then examine the Sekonic’s LCD.

I found the L-758D to be large, complex and to have too many simultaneous potential functions and too much going on the LCD display with too-small graphics and symbols. It is no doubt versatile but I would be happy with one of the simpler models in the range for the routine metering I need to do.

Calibration

If you shoot raw and habitually use a program like Adobe Camera Raw with auto adjustments set you can not use the meter calibration function. It only works if a fixed conversion is used for all files, or you shoot in-camera JPEGs and do not change the contrast or colour space and scene type settings.

The plain 18% grey back of the test card is ideal for white balancing and spot metering. The front side has an 18% grey field plus a central array of seven grey patches in 1/6th stop increments, plus and minus 0.5EV either side of 18% grey. Above this is a white strip 2.33 EV brighter than 18%, and below it a black strip 2.33EV darker.

Test file from the Konica Minolta Dynax 5D

While Sekonic issue L*a*b* values and densities for their £99.99 card (it goes from 3.6% to 90.7% reflectance, densities 0.04 to 1.44 LogD) they disclaim accuracy and say ‘not guaranteed as the performance of exposure profile target’.

Test file from the Sony Alpha 100 under identical lighting and lens conditions

In the CD-only user instructions you learn that you can equally well use a Kodak Greyscale and enter the data manually. The software, however, operates only with the Sekonic target for automatic entry. Even this is mainly manual; you must use Photoshop to read off the RGB values from each patch. It will not read a JPEG in the way that camera ICC profiling software reads a target image.

Light and lens problems

The recommendation is 45° copy lighting, but the total range of exposures needed to calibrate one DSLR fully is too great for most flash systems at such close range. You need to give plus three to minus three stops either side of a metered exposure, at each ISO speed you want to measure. You should also compare incident and reflected readings, and make tests using both flash and ambient light.

Even at ISO 400 my Elinchrom 300S heads, turned down to 1/16th power, need a neutral density filter fitting to make a complete set of exposures with ISO 400 and a lens which stops down to ƒ32, when placed five feet either side of the target.

The biggest speed deviations with DSLRs occur at even higher ISOs. Doing a full calibration is going to be difficult – I did not attempt it because I’m not keeping the meter, and it would have occupied a full half-day or maybe most of a day. But I would have needed some special type of light source to calibrate ISO 1600 or 3200.

It was useful to find out that two of our DSLRs used with twin wireless flash heads and auto exposure agreed with the Sekonic to within 1/10th of a stop, and one gave 1/3rd of a stop overexposure.

For quick operation, without a camera calibration for dynamic range and clipping point data, you don’t need the ±3 stops business. You don’t really need the Sekonic card, a good 18% grey card will do fine. Take a shot at each ISO setting, as measured by the Sekonic meter, using a medium lens aperture (least likely to have errors) and medium flashpower if possible (ditto). Open the JPEG in Photoshop, check the Green channel RGB levels in ‘Info’ and this should be within the range 116 to 120 (118 is the target figure). The 1/6th stop steps either side of G=118 are roughly in intervals of 8 on the lighter side and 7 on the darker side but cameras do not have linear response, and Sekonic only work within +/-2 units of the 256 value G scale.

Once you have completed all your entries, the meter is connected to the computer by its supplied USB cable, and the program recognises its presence. You can then upload the new calibration to the meter. Each calibration is recalled using a memory menu on the L-758D, and you must of course remember which storage register applies to which camera.

If you think any of this is slightly complicated, don’t buy the Sekonic L-758D for its programmable camera customisation. Buy it for its excellent performance as a multifunction flash/ambient meter with wireless Pocket Wizard compatible triggering upgrade option, and all the features you’ll find in the best meters of the last decade rolled into one.

The Sekonic L-758D meter is imported to UK by JP Distribution, and has a retail price (without the calibration target or the Pocket Wizard adaptor) of £398.99 including VAT.

– David Kilpatrick FBIPP Hon FMPA

5 Comments

  • Thanks for the info , will do a calibration on the 1dx ans see how it looks ,have done a custom WB , it came out very warm on the card but we will see. The 758 without calibrating shows up as 2stops under exposing . Which is quite high as the 7d was only a couple of tenths out.
    Thanks for you help
    David

  • I have a question , when calibrating a camera that measures against a 18% Gary card , how would you calibrate a canon 1dx that metres in RGB. Is it the same and you have to calibrate against the gray card.
    Regards David

    • Still the same grey card. You need I guess to know the value of 18% grey in RGB and that depends on the colour profile in use, but the software handles that. 50% grey is 128-128-128, 25% is 64-64-64, 12.5% is 32-32-32 etc. Usually the camera will ‘lift’ 18% a bit so it will be close to 50-50-50 for a normal looking image contrast and range from shadows to highlights.

  • Thank you for useful review/test!

    In comparison to other Seconic Light meters this one has reflected light measurement function. Is this function useful? Did you see the difference for landscapes in comparison with in camera metering system?

    You are writing “Unlike the Gossen Spotmaster F you don’t get information shown in the finder…” hovewer in Sekonic Brochure is picture with Spot Viewfinder and text “Its large, bright viewfinder with diopter correction and full-information data display give you everything you need to make the right exposure decisions without having to take your eye from the eyepiece.” Is it different model, L758DR?

  • Thanks very much for publishing this. I have a bit of a weakness for gadgets …………. provided they perform some useful function, aid productiviity, and the cost-benefit ratio is good.

    I have liked the Sekonic 758D from “day 1” but have always been a little reluctant to purchase for the following reasons: I couldn’t get any useful information of the kind you have published from Sekonic prior to purchase; the cost seemed nuts especially considering that they were charging extra for the calibration target which from many outlets also meant making a serperate special order; I also thought that for the price they should provide some VERY GOOD ready made profiles for download (they did initially,but for some reason withdrew them); I was a bit concerned as to workflow to set the whole calibration up (and your article addresses my concerns and it seems that even a man of your experience and with your equipment would have problems doing a full calibration); and finally, I was somewhat suscipicious as to whether or not such detailed calibration is necessary.

    I also got to thinking that perhaps, one could purchase the new Sekonic Calibration Target and produce one’s own calibration data (which of course you would have to write down and keep on hand in your kit bag) for use with one’s existing meter.

    Another thought that occured to me was whether such DIY data could be achieved with any meter and simply exposing a scene at various ISO and exposure settings.

    I think it would be great if you prepared an article, offering step-by-step instructions and advice, for those of us who are on a low budget and lacking the technical knowlege so as to enable us to get some useful calibration data using our existing light meters.

    Thank in advance.

    Regards,

Leave a Reply